Modules
Inertial Modules
|
|
Inertial Measurement Unit (RLVBIMU03)The RLVBIMU03 is an advanced inertial measurement sensor containing three accelerometers and three yaw rate sensors which provide roll, pitch and yaw rates. Using synchronous 24bit sampling for each of the internal sensors provides a high degree of accuracy with yaw rate resolution better than 0.5 degree per second and acceleration resolution down to 0.002g. Constructed with a splash-proof casing, with an IP66 rating, it is also ideal for use on boats or in harsh environments. This sensor can be used either directly connected to a VBOX, or it can also be used as a standalone device, with the CAN output fully configurable by the end user. It can also be used in a GPS/IMU integration process live on the VBOX3i to ensure supreme quality GPS data even when the external conditions are bad i.e. passing buildings, bridges and trees. Get more information on the IMU |
 |
Yaw Rate Sensor (RLVBYAW03)The Racelogic Yaw sensor with CAN and serial output houses a single axis MEMs Yaw rate sensor, and a twin axis G-sensor. The Yaw sensor can measure ±150º/s, and the accelerometers can measure ±1.7g. Inside there is also a temperature sensor. Each Yaw rate sensor is calibrated on our stabilised turntable in environmental chamber, so that a full temperature calibration is carried out from -20 to +50ºC. This gives the Yaw rate sensor a very high stability of less than 70º per hour. This sensor can be used either directly connected to a VBOX, or it can also be used as a standalone device, with the CAN output fully configurable by the end user.Get more information on the Yaw Rate Sensor |
Input Modules
 |
Frequency Input Module (RLVBFIM03)A 4-channel frequency capture and pulse counter unit. It accepts frequencies in the range of 1Hz to 20KHz, and the input circuit for each channel can accept a wide signal amplitude range from TTL sensors up to the higher voltages created by inductive sensors. This means that direct connection to ABS wheel speed sensors, RPM sources or fuel flow sensors is possible. The FIM03 can also be used in a “stand-alone” mode, outputting its input data over CAN to any other third party data logger.Get more information on the Frequency Input Module |
 |
Analogue Input Module (RLVBADC03)The RLVBADC03 is an 8-channel analogue voltage input module designed for use with the Racelogic VBOX. Each channel is electrically isolated and provides bipolar voltage measurement up to ±50v with a DC accuracy of 400µV. Isolated, regulated 5v and 12v supplies are available on the main 25-way connector in addition to a supply voltage connection. The ADC03 can also be used in a “stand-alone” mode, outputting its input data over CAN to any other third party data logger.Get more information on the Analogue Input Module |
 |
Strain Gauge Amplifier (RLVBSGA01)The SGA01 is a two-channel user adjustable strain gauge amplifier. Each channel is DC isolated and designed for full-bridge operation, but can be adapted for use in half-bridge and quarter-bridge applications.Get more information on the Strain Gauge Amplifier |
 |
Vehicle CAN Interface (RLVBCAN02)The RLVBCAN02 is designed to allow logging of vehicle CAN bus data by the Racelogic VBOX. Acting as a gateway, it collects user defined CAN messages from the vehicle Bus and transfers them to the VBOX. Special Racelogic researched CAN data sets are available from the Website for a number of different vehicles, allowing easy logging of RPM, Wheel speeds, Throttle angle etc.Get more information on the CAN Interface |
 |
Thermocouple Interface (RLVBTC8)The RLVBTC8 is an 8 channel K-Type thermocouple input module. Standard accuracy is ±0.3°C using the supplied terminal connector block with integral cold junction compensation. Also available is the RLVBACS002 dynamic cold junction interface to provide optimum performance of ±0.1°C. The TC8 can also be used in a "stand-alone" mode, outputting its input data over CAN to any other third party data logger. Get more information on the Thermocouple Interface |
|
|
 |
Micro Input Module (RLVBMICIN01)The Micro Input Module is a highly cost effective unit that can accept one RPM and four analogue signals via a removable screw terminal.Compatible with every VBOX and Racelogic performance meter, this product is an ideal solution if only a small number of parameters are to be logged. Get more information on the Micro Input Module |
 |
Mini Input Module (RLVBMIM01)The Mini Input Module is a versatile unit that enables a VBOX to log a number of analogue, digital and thermocouple input signals. The module can accept eight analogue, two digital and two thermocouple inputs. When used in conjunction with a VBOX MINI, the MIM01 can also output one digital and one analogue signal. Connections are via a removable screw terminal. The MIM01 can also be used in a "stand-alone" mode, outputting its input data over CAN to any other third party data logger. Get more information on the Mini Input Module |
Output Modules
 |
CAN to Analogue Output Module (RLVBDAC01)The CAN to analogue output module is designed to convert CAN Bus data into voltage form. In this way it is possible to log data from a CAN Bus with data logging equipment not incorporating a CAN interface. Four analogue voltage outputs are available and these can be mapped using the supplied configuration software.Get more information on the CAN to Analogue Output Module |
 |
CAN Speed Interface (RLCSI01-v2)The Racelogic CAN Speed Interface is a convenient method of obtaining Engine Speed and Road Speed from almost any vehicle with a CAN bus. An optional cable is available for use with a vehicle's OBD socket, for those that carry relevant CAN information on their diagnostic ports. Get more information on the CAN Speed Interface |
Radio Links
 |
VBOX Telemetry ModulesThe VBOX Telemetry System uses high power radio modems capable of transmitting and receiving RS232 data at distances of up to 3.5km. Two radio telemetry modules may be used to transmit VBOX serial data from a remote unit to a laptop PC at a maximum rate of up to 20Hz. Modules can also be used to receive differential correction information (DGPS) from a Racelogic Base Station for local position correction. Get more information on the VBOX Telemetry System |
 |
VBOX Bluetooth Module (RLVBBT01)The VBOX Bluetooth Module is a general purpose Bluetooth adapter designed as an alternative to using a hard-wired serial connection between the VBOX and either a Q2 Tablet PC or a Laptop PC equipped with a Bluetooth interface, allowing for increased fl exibility of set-up by removing any cabling restrictions. With a range of up to 30m, the unit incorporates a KC-22 Bluetooth OEM Micro Module, designed for maximum performance in a minimal space The module offers serial communications at 115K baud rate, ensuring full data capture and transfer.Get more information on the VBOX Bluetooth Module |
